1 of 18888-24-227-G-00 rev. B • 07/130.80”-1.75”* (20-44 mm)23.5”-30.5”* (597-775 mm)41"-72" *(1041-1829 mm)22.5-88 lbs (10.2-40 kg)*User&ap
10 of 18888-24-227-G-00 rev. B • 07/139a b c dST3.9 x 16mm4x#46, Ø 0.081” (2mm)If your brake release handle is not aligned with the front edge of you
11 of 18888-24-227-G-00 rev. B • 07/13M2.9 x 8mm3x3x2x1011Capture the brake cable in the cable clip as illustrated, then use a Phillips screwdriver to
12 of 18888-24-227-G-00 rev. B • 07/131213Set the desk upright onto its legs.CAUTION!LIFT HAZARD!Two persons are required for this step. Failure to fo
13 of 18888-24-227-G-00 rev. B • 07/1314122.5 mmRemove the 4 brake stop screws before installing equipment.Remove the 2 stop screws from the legs then
14 of 18888-24-227-G-00 rev. B • 07/131615826-901-00WARNINGMoving Parts Can Crush And Cut IMPACT HAZARDFailure to heed this warning may result inserio
15 of 18888-24-227-G-00 rev. B • 07/13=14mm17Release the hand brake (on the right leg) and move the worksurface up to highest level.Push in the cover
16 of 18888-24-227-G-00 rev. B • 07/13=14mmAPPENDIX A - Minimize Lift TensionWARNING. Before removing mounted equipment (monitor, arm, stand CPU, etc.
17 of 18888-24-227-G-00 rev. B • 07/13122.5 mmAPPENDIX B - Inserting Stop ScrewsWARNING. Before shipping or storing the desk, or in cases where the de
18 of 18888-24-227-G-00 rev. B • 07/13Learn more about ergonomic computer use at:Más información sobre el uso ergonómico de ordenadores:Apprenez-en pl
2 of 18888-24-227-G-00 rev. B • 07/13826-901-00WARNINGMoving Parts Can Crush And Cut IMPACT HAZARDFailure to heed this warning may result inserious pe
3 of 18888-24-227-G-00 rev. B • 07/131234SafetyDO NOT REMOVE SCREWS!DO NOT REMOVE SCREWS!WARNING! Stop screws are pre-installed in this product to sec
4 of 18888-24-227-G-00 rev. B • 07/13WARNING! TIPPING HAZARD!When mounting accessories to the WorkFit-D, they must stay within the foot print. Do not
5 of 18888-24-227-G-00 rev. B • 07/13AB C12341x1x3x2x1x1x1/4” 14mm#21, Ø 0.19” (4.8mm)#46, Ø 0.081” (2mm)2x2.1262.12612.9925.118XX3.90035.197DIMENSION
6 of 18888-24-227-G-00 rev. B • 07/13Brake ReleaseUse Drill Bit #21, Ø 0.19” (4.8 mm) to drill these 9 holes 3/8” (9.5 mm) deep.Use Drill Bit #21, Ø 0
7 of 18888-24-227-G-00 rev. B • 07/13#21, Ø 0.19” (4.8mm)#46, Ø 0.081” (2mm)Brake ReleaseUse Drill Bit #21, Ø 0.19” (4.8 mm) to drill these 9 holes 3/
8 of 18888-24-227-G-00 rev. B • 07/138x#12-14 x 5/8”234Place the worksurface on a clean oor with the top side facing down.Carefully position the leg
9 of 18888-24-227-G-00 rev. B • 07/13M5 x 6mm9x16x#12-14 x 5/8”7865WARNINGKeep Brake Cables Away from Sync Rod and Crossbars During Installation!Failu
Comments to this Manuals